|
|
HANs V simpson hybrid
(Preview)
I guys
what are people's thourghts on both types of helmet restraints ?
|
LIAbillity
|
2
|
1250
|
|
|
|
|
|
GEAR HEAT TREATING?
(Preview)
I want to strengthen my factory gears in my trophykart motorbike engine. Does anyone know someone good who can heat treat, or magna flux, or polish or whatever is required! albins can make complete new gears, but I would like to try treating the originals,
|
jones off road
|
2
|
960
|
|
|
|
|
|
lightened flywheels
(Preview)
i can buy a lightened flywheel for my 1grfe (toyota 4.0lt v6) 18 pounds, versus 31 pounds std. comments, thoughts anyone?
|
TEBBA
|
2
|
940
|
|
|
|
|
|
Buggy tyres
(Preview)
Hi all,
Just got some BTR 15 x 4 front rims to replace the cracked centrelines. The centrelines are 16" so I will need new tyres.
Any suggestions for the 15 x 4 BTR on the front? 8ply+
Beam front, 2" drop spindles and around 1200kg car if that helps any one
|
Mallee Master
|
1
|
1112
|
|
|
|
|
|
what age?
(Preview)
Can a 16 year drive a single seat car in state and ARB level events?
|
boss truck
|
1
|
957
|
|
|
|
|
|
buggy body panel thickness
(Preview)
G'day, I was looking in the CAMS manual to find out what the minimum aluminium body panel thickness is? i could only find the roof and floor pan minimum thickness. is there anybody that can help me out please? Cheers Brad
|
Bradley
|
5
|
1083
|
|
|
|
|
|
Wilwood Brake Parts
(Preview)
Does anyone know where I can get Wilwood brake parts as I need Master cylinder kits for a 3/4 and 7/8. Also I need to know if the aluminium bodied kits fit the composite plastic bodied master cylinder. Any help would be great.
|
Pedroski
|
5
|
1014
|
|
|
|
|
|
Noise Testing
(Preview)
Attention Competitors/organisers, The Confederation of Australian Motor Sport conducts noise testing across all disciplines and levels of motor sport. This testing is conducted to ensure compliance with local civil authority requirements for noise pollution. CAMS takes integrity and su...
|
Webmaster
|
10
|
1375
|
|
|
|
|
|
Intercom
(Preview)
Hi, Looking at buying a new intercom for my buggy so was wondering intercoms are people using and whats your thoughts on them? Cam Ritche said a lot of people are using the PCI 10D? Are they worth spending the coin on them? Cheers Aaron
|
aaron_ktm29
|
2
|
967
|
|
|
|
|
|
Fuel system
(Preview)
Trying to decide how to do the fuel system on my class 4 truck. Originally I was going to have 2 separate fuel systems starting with a surge tank in the fuel cell, then 2 Carter's drawing from the surge tank through 2 filters and pick ups, feeding straight in to 2 044 pumps, then check valves and filters and...
|
DMK
|
4
|
975
|
|
|
|
|
|
Tap size for bleed nipple in a tatum 4 pot?
(Preview)
Hey, anyone know that tap size the bleed nipple sits in in a tatum 4 pot?
|
Wolf
|
0
|
803
|
|
|
|
|
|
turbo 400 trans rebuild help
(Preview)
hello again everyone. due to the vast success of this forums knowledge with my other problems, youre my first port of call for my new problem..... congratulations on being so clever! we took our Colorado to sealake for our first "serious hit out", prologued 3rd in class, started the race...
|
Dags777
|
15
|
1544
|
|
|
|
|
|
Mid Board Hubs
(Preview)
Just put some new bearings in my gear one mid boards. I took it for a 15 minute drive and found that the temp at rear seal was 76 degrees. On the side with original repacked bearings it was 46 degrees. The free play measured at rim edge is 0.05mm on the new bearings. Is this too hot? Any ideas? Thanks.
|
Dust eatin wheat cocky
|
1
|
1609
|
|
|
|
|
|
Motec dash
(Preview)
Hi all I'm running a motec cdl3 digital dash in my buggy I'm just curious if anyone else running a digital display dash what do they use to protect it from rain and mud during a race iv seen a haltech race pak dash that had a clear hard plastic cover over top but I can't find anything for motec any help or sug...
|
Hussler263
|
0
|
1088
|
|
|
|
|
|
CV boots
(Preview)
What brand CV boots do people use On 930 cv? And where did you get them?
|
nt
|
3
|
1143
|
|
|
|
|
|
where to
(Preview)
anyone know where to buy a 200mm vw clutch friction disc with the chevy spline? as i currently run a 200mm clutch and going to the weddle boxes needs a 1 1/8" 26 spline
|
spoiltone
|
5
|
1076
|
|
|
|
|
|
weddle hv-1
(
1 2
)
(Preview)
looking at making this thing reliable, and wanting to get rod of the 2ltr box and upgrade tranny, it seems i learning towards the weddle hv-1. but want some aussie input, have u had any troubles, what are they in and what is pushing them, where did you get it, and approx cost. and approx how much work it do...
|
spoiltone
|
36
|
8316
|
|
|
|
|
|
fan shroud vs no fan shroud?
(Preview)
We're putting in the new radiator. Debating whether or not to build a fan shroud and mount the fans to it leaving a 1 or 2 inch gap between the fan and the core, or build a bracket to bolt the fans <5mm from the core. Im curious to see if anyone has any recommendations or pitfalls... Cheers.
|
Wolf
|
10
|
1595
|
|
|
|
|
|
clutch problems
(Preview)
hi guys I need some help , un5 gearbox vw bellhousing 1uzfe engine . brought flywheel from morrie at trikk , clutch and pressure plate from rivmaster . clutch is a 6 plate paddle , pressure plate is a kennedy 3500 pound . the problem is I can move the clutch fork up to the pressure plate but not move it anymo...
|
shane
|
5
|
964
|
|
|
|
|
|
Nitrogen
(Preview)
Hey all, Is there anybody on the south coast with the gear to charge a pair of bike shocks with nitrogen, same sort of valve as normal (car ) I'm I Ulladulla & not planning a trip to Sydney anytime soon so a shorter trip would be nice. Thanks Wayne.
|
260
|
1
|
858
|
|
|
